Skip to main content

BATTERY COIL IGNITION SYSTEM

. 
BATTERY COIL IGNITION SYSTEM


The above figure shows the diagram of a battery coil ignition system. It contains two circuits like primary and secondary circuits. The primary circuit have a battery, Ignition switch, primary coil, CB point, and condenser. The secondary circuit having secondary coil, HT cable, distributor, rotor and spark plug.

When the driver turn on the Ignition switch, a low voltage current from the battery is passes through the primary circuit. At the same time the cam starts to rotates it cut off the current flow through it. So the current transmits the primary winding to secondary winding. It also helps to increases current low voltage to high voltage. This high voltage current flows to the distributor and spark plug through High Tension cable.

Labels:

Popular posts from this blog

HEAD LIGHT CIRCUIT - WITHOUT RELAY

  AIM: HEAD LIGHT CIRCUIT WITHOUT RELAY TOOLS & MATERIALS REQUIRED: 1. Screw driver 2. Combination plier 3. Wire striper 4. Copper leg 5. Insulation tape 6. Head light switch 7. Dipper switch 8. Battery clips 9. Battery -12v 10. Head lamp - 12v DIAGRAM PROCEDURE: 1. ബാറ്ററിയിൽ നിന്നുള്ള +ve terminal head light സ്വിച്ചിലേക്ക് fuse വഴി connect ചെയ്യുക. 2. Head light switch ൽ നിന്നുള്ള out, dipper switch ന്റെ center point ലേക്ക് connect ചെയ്യുക. 3. Dipper switch ൽ നിന്നുള്ള dim, bright വയറുകൾ head lamp ലെ low, high beam വയറുമായി യഥാക്രമം connect ചെയ്യുക. 4. Head lamp ൽ നിന്നുള്ള -ve വയർ, ബാറ്ററിയുടെ -ve terminal ലുമായി connect ചെയ്യുക. RESULT : Head light circuit - without relay വിജയകരമായി പൂർത്തീകരിച്ചു
Read more

CENTRIFUGAL CLUTCH

MAIN PARTS 1. Fly wheel 2. Clutch plate 3. Clutch shaft 4. Pressure plate 5. Clutch spring 6. Bell crank lever 7. Centrifugal weight 8. Crank shaft CONSTRUCTION In this type of clutch, centrifugal force is used to keep the clutch in the engaged position. It is operated automatically depending upon the engine speed. It has a fly wheel, clutch shaft, clutch plate, pressure plate, bell crank lever and a centrifugal weight. The bell crank lever is fitted in to the pressure plate with the help of a lever is called bell crank lever. WORKING A simple diagram of a centrifugal clutch is shown in the above figure. When the engine speed increases, the centrifugal weight (A) fly off due to the centrifugal force. At the same time bell crank lever (B) presses the pressure plate(C) and the clutch plate (D) on the flywheel against the springs(G). This makes the clutch engaged. The torsion of spring (G) is designed for disengage the clutch below 500 r.p.m. So the power can't be transmit...
Read more

FOUR STROKE DIESEL ENGINE / COMPRESSION IGNITION (CI) ENGINE

FOUR STROKE DIESEL ENGINE Constructional details A four stroke diesel engine consists of a cylinder with its one end fitted with a cover and the other end left open. The cover is provided with the inlet and exhaust valves. These inlet and exhaust valves are opened and closed by mechanically operated cams. The fuel injector is fitted at the top of the cover to atomize the fuel. A piston carrying rings reciprocates inside the cylinder. The piston is connected to the crankshaft through a connecting rod and crank. It converts the reciprocating motion of the piston into rotary motion. WORKING Suction or intake stroke Suction stroke starts when the piston is at the top dead centre and about to move downwards. At that time, the inlet valve is opened and exhaust valve is closed. Due to the downward movement of the pisto, partial vaccum is created inside the cylinder. (i.e. the volume in the cylinder increases while the Pressure decreases). Due to the pressure difference between the...
Read more